Blue Combi

zoom

Blue Combi

Wrap-around case packers series PL@NET with case formation and closure in continuous to pack products into cases or into trays and shrink wrapping machine series ST@R.

The series PL@NET is the result of the long-term Dimac's experience on case packers, the maximum of innovation and the market demands.

COMBI machines are based on a "top level" technology:

possibility to control all machine functions
easy and precise size change
high flexibility to handle every kind of container
machine automatic check-up
easy maintenance
high accessibility
machine solid and reliable

+/-

Technical specifications

Suitable for the following products

Available models

Distinguishing marks

	MULTIPRODUCTS “B.I.” SEPARATION SYSTEM (PATENTED) Control by photocells for correct product position and for minimum product accumulation in each lane, control for the fallen product. Alternate separation system composed by a mesh belt driven by a clutch and brake group to allow automatic the size change through the operator panel. Upper pressing unit to stabilize products during separation. .
	PRODUCTS TRANSFER GROUP WITH BARS After the collation of the products into the required configuration, the block of the products is transferred to couple with the tray or the pad. The group is complete with plastic lateral guide rails in order to obtain a perfect products compacting. The group is equipped with torque limiter that safeguards the bars group from eventual accidental stops.
	MAGASINE AND BLANK PICK-UP The blank is picked up from the magazine by a device with suction cups and vacuum. The magazine is adjustable and has an high capacity. The magazine is fully accessible for easier and faster loading. The patented pick-and-place system ensures maximum precision and reliability.
	CASE FORMATION (PATENTED) The case is formed "in-line". After the product has been coupled with the blank, the internal flaps are folded and the hot melt glue is applied; then the top of the case is folded and finally the external flaps are folded.
	TRAY FORMATION The tray is erected in continuous by wrap-around system. The first flap is folded with the arrival of the front teeth of the chain; during the way, the blank is coupled with the product. The back flap is folded by the rear teeth of the chain. Then there is the folding of the front lateral flaps with fixed contrasts while the back ones are folded by folders driven by a mechanical contrast. At this point the glue is applied on the side flaps which, while advancing in continuous motion, are folded by a pneumatic cam. Finally, the lateral flaps are lift to couple with the already glued flaps to complete the tray.
	FILM UNWINDING SYSTEM The film reel are placed on two pneumatic expanding shafts. The system is complete with manual sealer for film splicing. Film is kept constantly in tension thanks to a pneumatic compensation group. The film reel are disk braking, with direct action on the expanding shafts in order to allow the correct film tension at the beginning or at the end of the roll. The group is equipped with antistatic bars to eliminate electrostatic charges.
	FILM CONTROL AND CUTTING SYSTEM (PATENTED) Cutting group with rotating shaft driven by a friction brake group. Film unwinding and thrusting driven by servomotors. The group is equipped with pneumatic input for rollers opening, in order to allow an easier film insertion. The upper belt has a tilt opening which allows the full inspection of the cutting group, the blade replacement or the complete cleaning of the group.
	PRODUCTS WRAPPING (PATENTED) Film transport bars are fixed on a rotary support only on one side to allow a full accessibility to the wrapping group. Simple manual adjustments with digital counters allow to wrap a wide range of packs without any parts replacement. Also this group is equipped with torque limiter to safeguard from eventual accidental stops.
	SHRINK TUNNEL Products go on a mesh belt driven by rubber rollers. The belt tensioning is kept constant by a damper weight placed on the last part of the tunnel. The tunnel is equipped with external adjustment to optimise the air flows according to the pack configuration. Manual device to empty the tunnel when no voltage is supplied. Cooling fan placed at the end of the tunnel to force the beginning of the shrink. Lateral panels can be dismantled for resistances replacement.

More Info

Personal Data

Company *
First Name *
Surname *
Role
Address *
ZIP *
City / Town *
Country *
Phone *
FAX
E-mail *
What is your area of belonging?
How many people work in his company?
Are you a Robopac customer? Yes · No
More information about
Your Message

I would like to be contacted

Phone
E-mail
Mail
I would like receive the newsletter
Authorisation By filling in and sending this module, I hereby authorise the processing of the personal data I provide, for the purpose indicated in point a) above, in the manner and within the limits indicated by the information contained herein, in compliance with and by effect of art. 23 of Legislative Decree 196/03.